Coconut, Wood or Coal: How Feedstock Shapes the Process Route
1. The Routes Diverge Before the Furnace
A 1,000 t/y activated carbon line looks much the same at the furnace whether it runs coconut shell, sawdust or coal. The front end differs by half the capex.
Shell: wash, dry, crush. Wet shell at 12–18% moisture must drop below 8% before carbonisation, or steam inside the kiln drags the temperature down and the char stays under-carbonised. Screen off sub-1 mm fines — the gas stream carries them into the cyclone.
Wood: dry, grind, briquette. Sawdust at 0.15–0.25 t/m³ blows through a bed, so it is extruded into 6–10 mm rods at 0.6–0.8 t/m³. Feed moisture 10–15%: drier will not bind, wetter collapses at the die.
Coal: grind, blend, press. Pulverise to 90% passing 200 mesh, blend 20–30% coal tar or pitch, press into 5–10 mm pellets. Binder ratio sets final hardness; get it wrong and activation cannot rescue strength above 90%.
2. Carbonisation and Activation Are Not One Recipe
Carbonisation follows feedstock. Shell: 400–500 °C, oxygen-lean, externally heated; too hot and pore walls shrink so activation can no longer open them. Wood: 400–600 °C, internal combustion saves fuel but the temperature wanders. Coal: 500–650 °C, passing through its softening range to set the skeleton.
Activation: 850–950 °C, steam. Shell stays at 850–900 °C — thin walls react fast, and higher heat burns through, taking strength from 95% to under 90%. Coal runs 900–950 °C for dense structure. Wood sits between, but potassium and sodium in its ash catalyse burn-off, so residence time must be shorter.
Residence time: rotary 60–120 min, multiple-hearth 40–90 min, fluidised bed 20–40 min. Steam 1.5–3 t per tonne of carbon.
Yield splits the routes: 10–15% shell, 12–18% wood, 30–40% coal. For 1,000 t of output the shell line buys 7,000–10,000 t of dry shell, the coal line 2,500–3,300 t. Feedstock logistics decide profitability more often than equipment price.
3. Three Routes, Three Customers
Iodine overlaps — 900–1,100 mg/g shell, 800–1,000 wood, 900–1,050 coal — but pores do not. Shell is microporous and suits gas phase and drinking water. Wood is mesoporous, methylene blue 120–180 mg/g, and owns decolourisation. Coal is broad and wins on price and volume. Strength: shell ≥95%, coal 90–95%, wood 85–92%. Ash: 1.5–3%, 8–15%, 3–8%. Bulk density: 0.45–0.55 g/cm³ for shell and coal, 0.30–0.45 for wood.
Coal below 5% ash needs acid washing plus effluent treatment, a capex line routinely missing from quotes. Wood at 85–92% strength needs 10–15% make-up a year in a frequently backwashed filter, against under 5% for shell. Compare three-year cost, not unit price.
4. Feedstock and Product First, Furnace Last
Ask which feedstock you can secure within 300 km, at what price, for how many years — not which is best. Feedstock is usually the largest single cost, and beyond 300 km freight eats the margin. Then fix the specification: iodine 1,000 or 900, ash below 3% or not. Only then work back to the furnace: many grades at small volume point to a batch rotary kiln, one grade at volume to a continuous unit, a fluidised bed only where uniformity is critical and the carbon is high-end gas phase.
FAQ
Q: Can one line run all three feedstocks? A: Not at the front end. Shell needs drying, wood needs briquetting, coal needs binder. Switching rebuilds half the line.
Q: Where does the 10% versus 35% yield show up? A: In feedstock bought — 7,000–10,000 t of shell against 2,500–3,300 t of coal for the same output.
Q: Is low wood strength a disqualifier for water treatment? A: No, but count make-up and labour into the three-year cost before comparing price.
Keywords: coconut shell activated carbon, coal based activated carbon, wood activated carbon, process route
